Back up firmware

#27

@Opera, Thank you. Finally we have a more current image. Really would like to archive 1.8.7. If anyone has it, Please upload. Thanks.

#28

I’ll have to dig around and figure out what my last release was. It looks like ‘with me’ i have version 1.8.4 (June 18, 2015)

I thought i had a newer one but I would have to look on a back up drive.

#29

I have the image file of version 1.8.4.
Where should I upload it?

#30

@J_Schmidt Thank you for letting us know.
I have my image to uploaded to @Insomnia 's Dropbox here

#31

Okay, Thanks. I just uploaded the 1.8.4 Software.

#32

It worked!
Finally, I can use heat bed!!
Thank you J_Schmidt!! :kiss:

#33

You´re welcome!
Speaking of the heated bed:
If you consider printing ABS, try covering the glass plate with kapton tape and use sandpaper to rughen the surface. Works fine for me. BUT: Do not use the bed temperature that Zeepro recommends: 110° is far too hot (at least for the Nunus ABS filament that I use). So when using the heated bed, I click the PLA or ABS button in the software and then manually adjust the temperature with the slider to 50°C for PLA or 90°C for ABS.
Most times, it´s also okay if you pull the plug after the first 5-6 millimetres height.

Have you also experienced a better print quality with the new software? I have the feeling that the layers are more accurate and stick together much better than in the previous 1.8.1.

#34

Improved ZIM stand with integrated spool holder (just kidding)

image.jpg2448×3264 966 KB

1 Like
#35

Hello,

Please does someone could provide me the 1.8.7 disk image ? I am in China and it is quite impossible to get connected to Dropbox.

Thank you for your help Guys

#36

Bump To get this thread up to the top of the list.

#37

I uploaded a rooted version of the 1.8.4 software.

If you update to this version, you will be able to ssh into the zim with ssh root@zim.local one you get your networking set up properly. The root password is “zim”

The root password is the only change on that image from J_Schmidt 1.8.4 image.

It would be nice if someone uploaded the latest update SD card image (presumably 1.8.7).

Jailbreaking ZIM after Zeepro stopped it´s services?
Jailbreaking ZIM after Zeepro stopped it´s services?
Jailbreaking ZIM after Zeepro stopped it´s services?
#38

i am having the same exact problem i am trying to install debian or cubian so that i can install octoprint but i have no success with connecting
have you?

#39

hi J_Schmidt do you have the 1.8.7 Software can i plz plz have it?? thank you vary much

#40

Hi!
I haven´t bee here for a while, sorry.
I do not have the 1.8.7 software, only the 1.8.4.

#41

Hey There J_Schmidt I bust up my zeepro empty sd card do you have the image for the empty sd card thank you.

#42

Do you have an imge for the empty sd card zip file can you post a link. thank you.

#43

Sorry, I only have the Printer-software. I switched to octoprint after Zeepro went off business, and I´m very happy with it.
I highly recommend you to buy a Raspberry and take the step to octoprint.

#44

I have never seen the 1.8.7
I am using the 1.8.4

Is there ONE person that is using the ZIM with 1.8.7 ?

#45

it seems to me the links here all dead.
I just shopped a mostly unused Zim.
Software 1.2 Firmware 1.1.0.3

Can someone please upload the last seen 1.8.4 (surely there are some improvements over my current one)

I would like to stay with the origin software.

#46

Hi @PstOne

I added this to the first post:

EDIT: LINKS!

Zeepro 1.8.4 IMG Backup

Zeepro 1.8.6 IMG Waffles (read about this here)